Korg LP-380-73 User Manual Page 17

  • Download
  • Add to my manuals
  • Print
  • Page
    / 71
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 16
17
The73-keyversionhasfourscrews(M4).Inaddition,
thepushrivetisnotincluded.
Screws (M6) x 6 pcs.
Screws (M4) x 8 pcs.
Caps x 6 pcs.
Push rivet x 1 pc.
Cord holder x 1 pc.
3. FastentheLP-380andthespeakerboxtotherightandle
sidepanelsusingeightscrews(M6).
Position the speaker box so that the speaker cord is on the le
side. In this position, the speaker (the side covered with cloth)
faces you.
First temporarily tighten* the screws on the right side panel,
and then temporarily tighten* the screws on the le side pan-
el.
* To temporarily tighten the screws is to tighten them leav-
ing a clearance of about 2 mm.
LP-380
the side covered with cloth
Speaker box
Screws
(M6)
Screws
(M6)
Side panel (right)
Side panel (left)
Positioning tab
Be careful not to pinch your ngers.
4. Connecttheaachedpedalcord,observingthecorrectori-
entation,totheconnectoronthereversesideofthepedal
unit,andthenengageitwithaslotinthepedalunit.
The pedal cord can be aached to or detached from the con-
nector with its locking tab held down.
Thepedalunitforthe73-keyversionhasadifferent
shape,butispreparedinthesameway.
Locking
tab
88-key version
73-key version
Assembling the Stand
Warning
● Atleastoneotherpersonmusthelpyouassem-
blethestand.
Caution during assembly
In order to assemble the stand safely, please observe the follow-
ing points.
• Make sure that you have the correct part in the correct orien-
tation, and perform the assembly in the order given.
Other cautions
Please check the following points aer assembly.
• Loosenedscrews
The screws may loosen as time passes after assembly. You
should periodically check whether any screws have become
loose. If you feel that the stand vibrates excessively, it is pos-
sible that screws have come loose. If so, re-tighten them.
• Whenmovingthedigitalpianotoanotherlocation
To move the assembled stand, remove the AC adapter cord
from the stand, close the key cover, and then move it slowly
with at least two people keeping it as level as possible.
• Disassembly
If you need to disassemble the stand, do so by reversing the steps
of the assembly procedure. Aer disassembly, keep the screws
and other parts in a safe place so that they are not lost.
The LP-380 should always be laid down before disas-
sembled.
Assembly procedure
You’ll need a Phillips (+) screwdriver.
1. Puttheprotectivesheet,whichhadcoveredtheLP-380,on
aatoor,andplacetheLP-380onthatsheetwithitsrear
facingtheoor.
In addition, place cloths or magazines so that you may easily
put your hands under the LP-380 when assembling and rais-
ing the stand.
Ensure that the LP-380’s key cover will not to open until
the end of the assembly.
Protective sheet
LP-380
2. Makesurethatallofthefollowingpartsareavailable.
The73-keyversiondoesnothaveapedalboard.Inad-
dition,thehardwareforinstallingthepedalboardis
notinstalledontheinsideofthesidepanels.
Anti-tipping Bracket (left)
Anti-tipping Bracket (right)
Pedal unit
Pedal board
Speaker box
Side panel (right)
Side panel
(left)
Pedal cord
Page view 16
1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 70 71

Comments to this Manuals

No comments