Korg LP-380-73 User Manual download pdf (Page 18)

10. Ensurethatthestandhasnogapsandisnottilted,andthat

allthescrewsaretightenedrmly.

11. Putcapsonthescrewheadsontherightandlesidepanels.

Caps

12. Connectthepedalcordandthespeakercordtotheconnec-

torsontherearoftheLP-380’sconnectorbox.

When connecting the pedal cord and the speaker cord, ob-

serve the correct orientations of the connectors.

The pedal cord or the speaker cord can be detached from the

connector with its locking tab held down.

Cord

holder

Speaker cord

Pedal cord

Speaker cord

Pedal cord

Locking tab

73-key version

13.Usethecordholdertoholdthepedalcord.

After securing the cord with the cord holder, ensure

that excess pressure is not applied to the connectors.

14.ConnectthededicatedcordtotheACadapter.Then,

plugtheACadapterintotheDCINconnector,and

wrapthecordaroundthecordhookofthepiano.For

details,referto“ConnectingthePower”onpage5.

15.PlacetheLP-380whereyouintendtouseit.Make

suretoplaceitinasafelocationwheretheoorisat

andstable.

Onthe73-keyversion,thepedalunitandstandare

separate,andonlythepedalcordisattachedtothe

stand.Becarefulwhenmovingthedigitalpianotoan-

otherlocation.

When seing the digital piano in place, make sure that

the stand does not rest on the AC adapter cable or pedal

cable.

For greater safety, be sure to attach the anti-tipping

brackets to the rear of the le and right side panels.

Check following assembly

□ Areanypartsleover?

If any parts are le over, carefully review the assembly proce-

dure to see where those parts should have been used.

□ Makesurethatallscrewsaretight.

5. Forthe88-keyversion,insertthepedalunitintothepedal

board,andthenfastenitbypressingapushrivetintothe

hole(abovethecutout)attherearofthepedalboard.

Aer pressing it into there, li the pedal board to check that

the pedals do not drop.

The push rivet will prevent the pedal unit from falling out.

Therefore, it cannot be fully fastened to the pedal board.

 Thisstepisnotnecessarywiththe73-keyversion.

Front

Front of pedal board

Rear of pedal board

Rear

Push

Push rivet

6. Forthe88-keyversion,temporarilyfastenthepedalboard

(withthepedalunitattached)tothehardwareinsidethe

sidepanelsofthestand,usingfourscrews(M4).

 Thisstepisnotnecessarywiththe73-keyversion.

Screws

(M4)

Screws

(M4)

7. Raisetheassembledstandslowlywithtwopeople.

8. Makesuretoaachtheanti-tippingbracketsbehindboth

sidepanels.Andtheanti-tippingbracketfastenedtothe

leofthecodeholderatthistime.

Joints between the side panels and the aached anti-tipping

brackets should be even (with no level dierence le).

Anti-tipping

Bracket

Screws (M4)

Reverse

Cord holder

73-key version

9. Then,firmlytightenallthescrewsthataretemporarily

tightenedinstep3and6.

When tightening the screws on the LP-380, adjust the up/

down and front/rear positions on the le and right side pan-

els so that they are equal.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 70 71

Comments to this Manuals

No comments

Korg LP-380-73 User Manual Page 18

Comments to this Manuals

Related products and manuals for Musical Instruments Korg LP-380-73